FFUN INSPECTION

There's nothing FFUN about buying a car that needs work right away. We put you and your passengers FIRST as part of our First. Fast. FFUN promise! It's about transparency when it comes to selling cars, and part of that means laying everything out on the table. Every vehicle we sell undergoes a meticulous 92-point vehicle inspection, and we'll even show you what we're checking out.

We don't look at four cup holders and count them as separate inspection points; we look at things that will keep you safe. We want you to be as confident as we are about your new car.

vehicle inspection

Every Point We Check

  • Meets/exceeds provincial inspection standards
  • Interior stains, holes or tears - cleaned or addressed
  • Tires at minimum 4/32 tread or replaced
  • Windshield damage repaired, non-repairable replaced
  • Brake pads measure a minimum of 4/32 or replaced
  • Paint chips and visible dents - touched up or repaired

See Inspection Details

 exterior

VEHICLE EXTERIOR

  • Lights
  • Taillights/Lenses
  • Mirrors
  • Wipers
  • Doors
  • Sun Roof
  • Convertible Tops
  • Aftermarket Components
  • Security Systems
 interior

VEHICLE EXTERIOR

  • Air Bags
  • Horn
  • Seats
  • Seat Belts
  • Gauges
  • Warning Lights
  • A/C and Heating
  • Radio/Entertainment
  • Power Locks
  • Tilt Wheel
  • Auxiliary Power Outlet
 under hood

UNDER THE HOOD

  • Fluids
  • Battery
  • Hood Latch
  • Filters
  • Belts
  • Clutch
  • Engine
  • Hoes
  • Motor Mounts
  • Charging System
 wheels

WHEELS

  • Tire Pressure
  • Bulges and Damage
  • Tread Depth
  • Tire Age
  • Spare Tire
  • Wells and Fenders
  • Hubcabs
  • Wheel Lugs
  • Studs
 brakes

BRAKES

  • Emergency breaks
  • ABS System
  • Pad Measurement
  • Shoe Measurement
  • Drums and Rotors
  • Leaks
  • Pull and Pulsation
 under body

UNDERBODY

  • No Frame Damage
  • Steering
  • Suspension
  • Axles
  • Transmission
  • Exhaust
  • Emissions
AIR BAGS
Passed
Passed
1.1
Airbag dash light must cycle off independantly of other system lights (check engine, ABS, etc.)
1.2
Airbag dash light must operate as designed
BRAKES / ABS
Passed
Passed
2.1
No leaking brake hoses
2.2
No pull during braking
2.3
No brake pulsation
2.4
Emergency brake must operate as designed
2.5
Master cylinder must not leak
2.6
Caliper pistons must not leak
2.7
ABS system must operate as designed under braking
2.8
ABS dash light must operate as designed
2.9
Wheel cylinders must not leak
2.1
All pads must measure a minimum of 4/32 above rivet or backing plate
2.11
All shoes must measure a minimum of 3/32 above rivet or backing plate at lowest point
2.12
All drums and rotors must meet manufacturers minimum specs
2.13
Must meet Provincial minimum requirements
FLUIDS
Passed
Passed
3.1
No locking gas caps
3.2
No addatives to prevent smoking, knocking, improper shifting, or hide mechanical failures
3.3
Diagnose low fluid conditions - (is system leaking)
3.4
All fluids must be in good condition - no burnt fluids
3.5
Fuel must be at 1/2 tank for delivery or pickup
3.6
All fluids must be topped off to fill line including oil, transmission, power steering, brake, coolant and washer fluid
3.7
Repair any leak that forms a drip
HORN
Passed
Passed
4.1
Must operate as designed
LIGHTS
Passed
Passed
4.3
Factory fog lights must work as designed. Aftermarket foglights can be removed if inop.
4.4
Interior indicator lights must operate - (turn signals, brights, etc)
4.5
Dash lights must operate as designed
4.6
Interior dome light must operate as designed
4.7
All exterior lights must operate as designed, including headlights, brights, parking lights, turn signals, brake lights, taillights, reverse lights, fog lights, and license plate lights
TAILLIGHTS / LENSES
Passed
Passed
5.1
Small cracks may be sealed with transparent glue to prevent white light from penetrating unless Provincial requirements require replacement
5.2
No holes or leaks in lenses (unless drilled for condensation removal)
MIRRORS
Passed
Passed
6.1
All power mirrors must operate as designed
6.2
Mirrors must hold adjustment
6.3
Vehicle must have all factory mirrors
6.4
Mirrors must not be cracked
SEAT BELTS
Passed
Passed
7.1
All belts must be buckled
7.2
All child safety seat latches must operate as designed
7.3
Belts must not have rips, tears or fraying
7.4
All seat belts must be fully functional (latches, ratchets, pre-tensioner, etc)
FRAME DAMAGE
Passed
Passed
8.1
No sub-frame or cradle damage (baseball size dent or greater/cracked-replace) continue to clarify-cosmetic/mechanical
8.2
No frame damage
TIRES
Passed
Passed
9.1
No studded tires
9.2
Same brand tires is not required.
9.3
White letters must match or be flipped to the inside
9.4
White walls must be flipped to the inside
9.5
All tires set at the recommended pressure
9.6
Must have spare tire, jack and lug wrench - spare must be properly inflated
9.7
All 4 tires must be same size unless specified by the manufacturer
9.8
No bulges, seperations or knots
9.9
No side wall damage
9.1
Minimum of 4/32 of tread remaining at lowest wear point of tire
9.11
Minimum of 2/32 of tread on outer 1" of tire tread
9.12
Full size spare tires must meet all tire standards
9.13
Tire age must not exceed 5 years, 9 months of age from tire mfg date at inspection
WHEELS
Passed
Passed
10.1
No rubbing wheel wells or fenders
10.2
Wheels must be rated for the vehicle
10.3
No excess wheel offset which may cause stress to the suspension
10.4
All 4 wheels must be same size unless specified by manufacturer
10.5
Wheels or hubcaps must match all 4 wheels
WHEEL LUGS / STUDS
Passed
Passed
11.1
All vehicles must have functional tools for locking lug nuts and/or aftermarket lug nuts
11.2
Must have all lug nuts (same size)
11.3
All wheel studs must be operational
11.4
Must have all wheel studs
11.5
All tires set at recommended pressure.
11.6
No broken lug nuts or studs, no missing lug nut caps.
GLASS
Passed
Passed
12.1
All power windows must operate from each window and from master switch
12.2
All windows must operate as designed
12.3
Rear defogger must operate as designed
12.4
No leaks
12.5
Do not tint windows
12.6
Remove tint if damaged or if not in compliance with state law
12.7
Repair windshield damage, replace non-repairable windshields
WIPERS
Passed
Passed
13.1
All jet sprayers must be operational
13.2
Wipers must "park" below drivers sight line
13.3
Must wipe clean and clear
13.4
Wipers must work on all speeds
13.5
No splits, cracks or dry rotted blades
13.6
All wipers must work (front and rear)
DRIVEABILITY
Passed
Passed
14.1
No excessive road noise, suspension noise, vibrations or pulling.
14.2
Odometer must work as designed
SEATS
Passed
Passed
15.1
All head restraints must be installed
15.2
Vans and SUV's must have third row seat if originally equipped with 3rd seat
15.3
All seats must operate as designed
BATTERY
Passed
Passed
16.1
Must pass load test
16.2
Terminals must be free of corrision or replaced
16.3
Cables must be secured to terminals
16.4
Must be fastened down to the vehicle
16.5
Must function correctly for the vehicle
KEYS
Passed
Passed
17.1
Repair or replace key fobs/remotes as needed all units must have fob/remote if equipped
17.2
Keys must operate all factory locks and ignition unless valet key or accessory key
HOOD LATCH
Passed
Passed
18.1
Primary and secondary hood latches must operate as designed
18.2
All releases (hood, trunk, fuel door) must function
STEERING / SUSPENSION
Passed
Passed
19.1
No play in steering wheel assembly (tilt)
19.2
No stiffness in steering
19.3
No leaks in steering or suspension components.
19.4
Suspension system must operate and function as designed.
DOORS
Passed
Passed
20.1
All doors must open from inside and outside handles
20.2
All trunk, hood, liftgate and glass struts/shocks must hold and function as designed
AXLES
Passed
Passed
21.1
No torn axle boots
21.2
No abnormal axle or bearing noises (clicking, howling, etc)
FILTERS
Passed
Passed
22.1
Air filter must be clean, without tears and free of debris
22.2
Cabin air filter must be clean, without tears and free of debris
BELTS
Passed
Passed
23.1
No broken, torn or cracked belts (no cracks beyond ribs of belt)
CHECK ENGINE LIGHTS
Passed
Passed
24.1
Check Engine, Service Engine, Maintenance Required lights are not on
24.2
Check engine light or service engine dash light must operate as designed
CHECK OTHER WARNING LIGHTS
Passed
Passed
24.4
All warning lights turn off after the vehicle is started
24.5
All warning lights come on when key is cycled to the "ON" position
CLUTCH
Passed
Passed
25.1
No grinding (synchronizers)
25.2
Replace throw-out bearing and pilot bearing if replacing clutch
25.3
No throw-out bearing noise
25.4
No leaking slave cylinder or master cylinder
25.5
No slipping
ENGINE
Passed
Passed
26.1
No sludge in engines
26.2
No misfires, stumbling, hesitation or rough running conditions
26.3
No oil addatives
26.4
No timing belt / chain noise (including tensioners)
26.5
No abnormal valve-train noise
26.6
No engine knocks cold or hot which the manufacturer has not deemed normal
26.7
No abnormal engine smoke
EMISSIONS
Passed
Passed
27.1
Vehicle passes Provincial emission requirements
27.2
Vacuum hoses in good condition (no splits or cracks)
27.3
All emission equipment present
EXHAUST
Passed
Passed
28.1
No abnormal exhaust noise
28.2
Tailpipe extends beyond the body of the vehicle
28.3
Exhaust system hung safely and securely
28.4
No exhaust leaks cold or hot
GAUGES
Passed
Passed
29.1
No signs of odometer tampering
29.2
Cluster cover must be clear and free of damage
29.3
Gauges must operate as designed
HOSES
Passed
Passed
30.1
No cracks, leaks, bulges or dry rot
MOTOR MOUNTS
Passed
Passed
31.1
Replace if saturated with oil
31.2
Replace if mounts bottom out (clunks, thumps, bangs)
31.3
Replace if broken
TRANSMISSION
Passed
Passed
32.1
4WD operated normally in high and low
32.2
All manual gears operate normally
32.3
Reverse works normally
32.4
Overdrive works normally
32.5
Passing gear works normally
32.6
No slipping, delay shift, hard shift
CHARGING SYSTEM
Passed
Passed
33.1
Charging system must operate as designed
AIR CONDITIONING / HEATING SYSTEM
Passed
Passed
34.1
All A/C and heat controls must work as designed (front and rear)
34.2
Heat and defrost must work as designed
34.3
A/C must operate as designed
COOLING SYSTEM
Passed
Passed
35.1
Vehicle operates in the normal temperature range
35.2
No leaks
35.3
Coolant must be factory specifications
35.4
Cooling system must operate as designed
RADIO/ENTERTAINMENT
Passed
Passed
36.1
Radio/entertainment display must work
36.2
All radio/entertainment components and controls must function as designed (aux, c/d, dvd, usb, etc.)
36.3
All speakers must operate as designed
CONVERTIBLE TOPS
Passed
Passed
37.1
No rips or tears
37.2
No leaks
37.3
Convertible top and components must operate as designed
SUN ROOF
Passed
Passed
38.1
No leaks in sunroof
38.2
Non-factory sunroofs must operate as designed
38.3
Must be operational
POWER LOCKS
Passed
Passed
39.1
All power locks must operate
TILT WHEEL
Passed
Passed
40.1
Tilt wheel mechanism must operate as designed
CRUISE CONTROL
Passed
Passed
41.1
Cruise control must operate as designed
AUXILLARY POWER OUTLETS / LIGHTER ELEMENT
Passed
Passed
42.1
Missing elements must be replaced or capped
42.2
Lighter elements must function as designed
42.3
Power outlets must operate as designed
SECURITY SYSTEMS
Passed
Passed
43.1
Repair OEM system
43.2
Remove aftermarket security systems (even if operational)
AFTERMARKET COMPONENTS
Passed
Passed
44.1
Aftermarket exhaust must fit vehicle and must have all emissions components.
44.2
Aftermarket cold air intake systems must function to manufacturer minimum specs and can not interfere with emissions equipment. Components must be properly installed.
44.3
Aftermarket components and/or accessories must be properly installed and must not interfere with the operation of the vehicle.
EXTERIOR
Passed
Passed
50.1
HV scratches must be repaired if they exceed 3 inches in length or are wider than 1/4 of an inch. Multiple scratches must not exceed an accumulative of 6 inches in length per panel.
50.2
LV scratches must be repaired if they exceed 6 inches in length or are wider than 1/4 of an inch. Multiple scratches must not exceed an accumulative of 18 inches in length per panel.
50.3
HV dents must be repaired if they are larger than 1 inch in diameter. No more than 2 dents in the same panel.
50.4
LV dents must be repaired if they are larger than 2 inches in diameter. No more than 2 dents in the same panel.
50.5
Punctures and tears in bumpers must be repaired.
50.6
Scuffs or spider cracking must not exceed a 2 inch by 3 inch area.
50.7
No faded or missmatched bumpers.
50.8
Add a bedliners to truck beds with excessive or dissapropriate amounts of scratches, dents and/or body damage.
50.9
Bed toppers and tool boxes must have a working key
50.1
Bed rail caps can be installed to cover any holes in the bed rail due to tool box or topper removal.
50.11
All oxidation, yellowing, and surface cracking must be removed through restoration or replacement.
50.12
No moisture in headlamp
50.13
No missing or broken moldings or emblems
50.14
All moldings and emblems must be firmly attached
50.15
No fading or discoloration of emblems.
50.16
Both front and rear emblems must match
50.17
Any emblem with writing/words must NOT be blacked out
50.18
No mismatched panels.
50.19
No dirt or "trash" in paint.
50.2
Any panel with clear coat damaged or missing must be repaired
50.21
Bug damage/acid spots must not be greater than 1" in diameter
50.22
Bug damage/acid spots must not exceed more than 10 spots per panel
50.23
Bug damage/acid spots/paint chips must not exceed more than 5 spots in any 1sq ft area
50.24
All non factory badging/stickers must be removed from the vehicle
50.25
Paint chips must fit within the Non-Seat burn limit template
50.26
No rust spots on painted surfaces
INTERIOR
Passed
Passed
60.1
Cuts, rips and tears must not exceed 1/2 inch in diameter. No more than 1 cuts/rips/tears per panel
60.2
Holes or burns must not exceed 1/4 inch in diameter. No more than 1 holes per panel
60.3
Stains must not exceed 1/2" in diameter, no more than two 1/2" stains per panel
60.4
Wear - light wear is acceptable as long as the material is not compromised and is clean
60.5
All interior displays (radio, climate control, gauges, buttons) must be clearly legible
60.6
No unpleasant odors
60.7
Scuffs in panels must not exceed a 2 inch by 3 inch area
60.8
Scratches on panels must not exceed 3 inches and must be less than 1/4 inch wide.
60.9
No cuts, rips or tears in seats
60.1
No burn holes
60.11
No stains
60.12
No missing or broken trim panels
ajax loader2
Submit